Elenco Electronics rc snap rover Instruções de Operação

Copyright © 2008 by Elenco®Electronics, Inc. All rights reserved. No part of this book shall be reproduced by REV-B Revised 2008 753131any means;

-9-The Snap Circuits®Kit uses electronic blocks that snap onto a clear plasticbase grid to build different circuits. These blocks have different color

-10-Project #2OBJECTIVE: To build a remote control vehicle.Remote Control RoverChannelswitchonremotecontrolunit.Install six (6) “AA” batteries into t

Project #3OBJECTIVE: To make a rotating light.LighthouseBuild the circuit, place the base gridcentered on the Rover body, andconnect the jumper wires

-12-Rover Rear (upside down)Project #5OBJECTIVE: To build a remote control vehicle with two soundlevels.Two-Sound RoverBuild the circuit shown and tu

-13-Project #7OBJECTIVE: To learn about Morse code.Build the circuit, connect the jumper wires, and turnon the slide switch (S1). Turn on the remote

-14-Project #9OBJECTIVE: To show how capacitors slow things down.Build the circuit, place the base grid on theRover body, and connect the jumper wire

-15-Project #11OBJECTIVE: To build a circuit with sound and light.Sound & LightOBJECTIVE: To show how capacitors store electrical charge.Electri

-16-Build the circuit shown and turn on the slide switch(S1). Turn on the remote control unit, extend theantenna, and press the left button. The LED (

-17-Project #15OBJECTIVE: To compare types of circuits.When More Are LessProject #16OBJECTIVE: To compare types of circuits.When More Are MoreBuild

-18-Build the circuit at left and connect the jumper wires to it, but leave the looseends of the green and purple jumpers unconnected for now. There i

-1-Basic Troubleshooting 1Parts List 2How to Use It 3About Your SnapCircuits Parts 4How It Works 5, 6General OperatingInstructions 6DO’s and DON’Ts of

-19-Project #19OBJECTIVE: To show how water conducts electricity.Build the circuit at left and connect the jumper wires to it,but leave the loose end

-20-Project #21 One-Way LightOBJECTIVE: To show how an LED works.Build the circuit, place the base gridcentered on the Rover body, andconnect the j

-21-OTHER SNAP CIRCUITS®PRODUCTS!FM RadioModel SCP-02Motion DetectorModel SCP-03Music BoxModel SCP-04Space BattleModel SCP-05Flying SaucerModel SCP-06

-22-Project #B1Machine Gun RoverProject #B2 Six Function R/CThe remote control levers and buttons activate six functions: three LEDs(D1,•D2, &•D

Elenco®Electronics, Inc.150 Carpenter Avenue • Wheeling, IL 60090(847) 541-3800 • Fax: (847) 520-0085 • Website: www.elenco.com • e-mail: elenco@e

Note: If you have a more advanced model, there are additional part lists in the other project manuals.Important: If any parts are missing or damaged,

-3-Install six “AA” batteries (not included) into the bottom of the Roverbody and one 9V•battery (not included) into the remote control unit.Install t

(Part designs are subject to change without notice).Note: If you have a more advanced Model, there is additional information inyour other project manu

-5-Remote Control Transmitter:When the levers in the Remote Control Unit are pushed, electricalcontacts are made connecting the 9V battery power to th

General Operating Instructions-6-Wheel shaftMotor gearSpins 128 timesfaster than wheelsHow It Works (continued)Rover Drive Mechanism:The small gear on

-7-After building the circuits given in this booklet, you may wish to experimenton your own. Use the projects in this booklet as a guide, as manyimpor

-8-Advanced Troubleshooting (Adult supervision recommended)Elenco®Electronics is not responsible for parts damaged due toincorrect wiring.If you suspe